本产品为反应型材料，A B组混合后涂刷，本产品为水性涂料，安全无毒，绿色环保。

形成的防水层抗水压力强、耐老化、与建筑粘结力强、成膜后耐水漫泡、耐候性好?

本产品涂刷于水泥面，有很好的渗透效果，成膜后硬度很高.

适用范围：

用于建筑各种水泥面的背水面修复，防水补漏.

施工注意：

1. 基面清理后(无油污无浮尘），先在表面涂刷一层 << 堵涂-抗渗速凝粉>> .

表面潮湿可以直接把堵涂-抗渗速凝粉加水后调成泥浆状，直接涂刷在表面?

表面有裂缝的，需对裂缝先开槽，后需加少量水(1包加0.6 ~ 0.8 K G水），菌S将开槽的部分抹平?

2. 再将背水面涂料A、B ( 4:1)组在桶中混合，用手提揽拌器揽拌5?10分钟，使之充分均匀，在1小时内用 完，本产品为反应型材料，超过时间使用涂料会变稠，影响涂刷.

3. 可适用刷涂、滚涂或喷涂，涂覆三遍以上，每遍间隔时间为2W钟左右，以手触表干为准，使涂层厚度大 于 0.5mmo

4. 涂料施工后，24h内避免菌g受水流冲击，常温下，72小时后可进入下道工序施工，如批膩子，贴瓷砖 等。

温馨提示：

再刷最后一S涂料后，在其表面撒上一层细砂，固化后再贴瓷砖或批膩子，效果更佳。

所用工具皆可用水清洗。

保质期：贮存温度5°C-40°C ,存阴凉干燥处，在正常运输、贮存条件下，产品保质期自生产之曰起一年。 参考用量：约0.6-0.7kg/nf (基面平整），D/YZ 001-2017。

堵涂（背水面防水修复涂料） 家装产品……2.5KG/桶

This product is a reactive material. After mixing with A B group, this product is water-based paint, safenon-toxic,environmentally friendly.

The formed waterproof layer is resistant to water pressure, aging resistance, strong adhesion to the building, water-resistant foaming after film formation,good weather resistance.

This product is applied to the cement surfacehas a good penetration effect. The hardness after film formation is very high.

Scope of application:

Used for the back surface repair of various cement surfaces, waterprooftrapping.

Construction attention:

1. After the base surface is cleaned (no oilno floating dust), first apply a layer on the surface << Blocking coating - anti-seepage quick-setting powder>>.

If the surface is wet, the plug-coating quick-setting quick-setting powder can be directly added to the waterthen adjusted a slurry shape, which is directly applied to the surface.

If there is a crack on the surface, it is necessary to first slot the crack,then add a small amount of water (1 pack plus 0.6 ~ 0.8 K G water). Will the bacteria S smooth the grooved part?

2. Mix the back water surface paints AB (4:1) in a bucketmix them for 5 to 10 minutes with a hand blender to make them fully uniformuse up within 1 hour. This product is reactive. Material, over time, the coating will thickenaffect the application.

3. It can be applied by brushing, rolling spraying. It can be applied more than three times. The interval time is about 2W. The thickness of the coating is greater than 0.5mmo.

4. After the paint is applied, avoid the bacteria g being affected by the water flow within 24 hours. At normal temperature, after 72 hours, you can enter the next process, such as batching puttytiling.

Tips:

After brushing the last S coating, a layer of fine sand is sprinkled on the surface,after curing, the tile the putty is applied,the effect is better.

The tools used can be washed with water.

Shelf life: storage temperature 5 ° C -40 ° C, stored in a cool dry place, under normal transportationstorage conditions, product shelf life the start of production for one year. Reference dosage: about 0.6-0.7kg/nf (base leveling), D/YZ 001-2017.

Blocking coating (backwater surface waterproofing repair coating) Home improvement products...2.5KG/barrel

来源：聚王牌防水网